How to Replace an new audi keys audi q3 key replacement Cost (moparwiki.win) G28 Engine Speed Sensor
Charles the Humble Technician shows you how to replace the G28 Engine Speed Sensor. This sensor is located near the transmission's edge, above the flywheel gear. It transmits a signal to the ECU via a grey wire (T55/49) which is then sent to the tachometer in the instrument cluster.
1. Engine Speed Sensor
The grey wire is located on the edge of transmission, above the flywheel ring. This sensor sends a signal via the grey wire to pin T55/49. The ECU uses this information to control fuel and boost. It also sends signals to the G5 tachometer inside the instrument cluster.
The sensor is used as a reference point to connect with the G40 Camshaft Position Sensor. The ecu must be aware of when the crankshaft has reached TDC and also the position of the camshaft, so that it can activate the spark and injectors.
If this sensor fails when it fails, the ECU will display a P00160 error code. This indicates that the Crank Shaft is not in line with the Intake Camshaft. It could also be a sign of the possibility of a chain stretch or jump in the chain link of the upper chain. However the code will not be displayed on its own without additional information from other sensors (G4 and G40).
Testing is a bit challenging because there are two connector pins, and they perform different functions but the best method to test it is to measure resistance between the sensor and the ECU. It should read approximately 1000 ohms when the sensor is in full operation. Examine for evidence of coolant or oil in the connector bay if you are experiencing issues with this component.
2. Injectors
Yesterday, while accelerating at full speed from the highway paytoll, I experienced a big cut in power as if the engine was running out of gas or injectors aren't firing any more. Today, i pulled out the spark plugs. Three were soaked with gazoline and the 4th one was dry. I put a piece of tissue over each hole in the injector and when i start the engine without sparks, the ones with gazoline jump out. The 4th one remains closed. I checked the ground connection on ECU pins 14/55,30/55 and 48/55 I get zero Ohm. I think the issue is somewhere else.
I also tried to reset the PID without success. The car key replacement audi will start when the G28 is disconnected, but it is running fine with the G28 connected. However the intermittent misfire issue still occurs at higher RPM. The temperature sensor for coolant (G62) shows the wrong temp value -49c even when i unplug it. I also noticed that the oil gauge in the cockpit shows 2 bars while the actual pressure is zero.
I don't know what to do. I believe that I've ruled everything else out. However, i'm afraid that I might have missed something. If anyone has any ideas please chime in! TIA!
3. Fuel Pump
The fuel pump on the g28 is activated by a signal from the RPM sensor. The GM-style transmitter is the same as the G4 and both function in the 80 100 200, UrS and RS2 cars which is why you can easily locate one at a junkyard or at a parts store. It is easy to test them: simply put your DMM into resistance mode and test the distance between pins 1 and 2 (with the bump at the connector's end facing up). They must be infinite Ohms.
4. ECU
Our 20vt turbo (3B AAN, ABY, and ADU) engines have an ECU that has to know the speed and position of the crankshaft in order to make a decision about timing of the fuel injector, for example. To accomplish this, it makes use of a Crank Position Sensor (G4) and an Engine Speed Sensor (G28). If you have a problem with either of these sensors, the diagnostic scanner will show codes that could lead to an engine shut down.
Some of the signs of a malfunctioning G28 sensor are an inaccurate rev counter for the gearbox the gears are shifting faster than normal and/or misfiring when in gear. If you are experiencing any of these issues it is likely that your sensor is going bad and needs replacing. The good news is that they are very affordable and readily available particularly when you're looking at the Bosch sensor, which is what we have. You can also choose the GM version of this unit is also a good choice.
5. Tachometer
A faulty engine speed sensor could be a cause for numerous problems in your vehicle. It is a crucial part of the audi replacement key service's transmission as it sends information to the ECU about how fast or slow the car's crankshaft is turning. When this sensor fails, it will disrupt the performance of the transmission, as well as the rest of the car's components.
The G5 engine speed sensor is located at the edge of the transmission, above the flywheel ring gear and transmits a signal to the ECU at pin T55/49, via a grey wire. The ECU then processes this signal to regulate the flow of fuel, timig and boost as well as sends it on to the G5 Tachometer located in the instrument cluster. You can check for sensor failure by checking continuity from the sensor to the tachometer. Also, you can examine the continuity between pins T55/49 of the ECU and pin T6a/1 of the instrument cluster (trace [79]), and between pin T6a/1 as well as pin T26a/12. You should detect the resistance to be around 1000 ohms between these points. This is a common feature across the audi keyless entry 80-100-200-RS2 range, from the 1985 MC all the way up to the 1997 UrS An and 1995 RS2 DU You may also find them in wrecking yards.