How to Replace an Replacement audi tt replacement key a4 key (yogicentral.science) G28 Engine Speed Sensor
Charles the Humble Technician shows you how to replace the G28 Engine Speed Sensor. The sensor is located at the edge of transmission just above the flywheel gear. It sends a message to the ECU through a grey wire T55/49, then to the tachometer located on the instrument cluster.
1. Engine Speed Sensor
The grey wire is situated on the edge of transmission, just above the flywheel ring. The sensor transmits signals through the grey wire to pin T55/49. The ECU uses this information to regulate the amount of fuel and boost. It also sends an alert to the G5 Tachometer in instrument cluster.
The sensor serves as a reference point to connect with the G40 Camshaft Position Sensor. The ecu must know when the crankshaft has reached TDC, and where the camshaft lies in order to activate the spark and injectors.
If this sensor fails when it fails, the ECU will display a P00160 error code. This indicates that the Crank Shaft is out of sync with the Intake Camshaft. It could also indicate the possibility of a chain stretch or jumped chain link in the upper chain of timing. The code will not appear without the additional information provided by other sensors (G4 or G40).
It can be a bit difficult to test because there are various connector pins, and each one has different functions. The best method for doing this is by measuring the resistance between the ECU and the sensor. When the sensor is fully operational, it should be reading around 1000 ohms. If you're having issues with this part, check for signs of oil or coolant in the connector bay.
2. Injectors
Yesterday, when accelerating from highway paytoll at maximum speed I noticed a massive drop in power. It was as if the engine was running out of gas. Or my injectors were not firing. This morning i pull out the spark plugs, 3 were soaked with gazoline and the fourth one was dry. I put a piece of tissue over each injector hole, and when I start the engine without sparks, the 3 with gazoline jump right out. The 4th one remains shut. I tried to test the ground connections of ECU pins 14,30, and 48/55. I found 0ohm. I assume that the problem is elsewhere.
I also tried to reset the PID with no success. The car will start when the G28 is disconnected, but it is running fine with the G28 plugged in. However the intermittent misfire issue still occurs at higher RPM. The temperature sensor for coolant (G62) shows the wrong temperature of -49c even when i unplug it. I also noticed that the oil pressure gauge in the cockpit is showing 2 bar while the actual pressure is 0.0 if i crank up the engine.
I'm not sure what to do. I think I've ruled everything else out. But i am afraid I may have missed something. Please let me know if you have any ideas! TIA!
3. Fuel Pump
The fuel pump in the g28 receives a signal from the RPM sensor. The GM-style sensor is identical to the G4 and both are used in the 80, 100, 200, UrS and RS2 cars so you can easily find one at a junkyard or Audi key Fobs in a local parts store. It is easy to test them - just switch your DMM into resistance mode and determine the distance between pins 1 and 2 (with the bump at the connector's end facing up). They should be infinite Ohms.
4. ECU
The ECU in our 20vt turbo (3B AAN ABY ADU) engines must be aware of the speed and position of the crankshaft to make decisions regarding timing of the fuel injector, etc. It uses a Crank Position Sensor G4 and an Engine Speed Sensor G28 to achieve this. If either of these goes wrong, you will receive codes on the diagnostic scanner which can cause the engine to shut down.
A malfunctioning G28 sensor could result in an inaccurate speed counter for the gearbox or a gearbox that shifts more quickly than normal, and/or a misfire in gear. If you are experiencing any of these issues it is most likely that your sensor is failing and should be replaced. The good news is that they are very cheap and easily accessible particularly if you're looking at the Bosch unit which is what ours are. Alternatively, GM's version of this component is an option.
5. Tachometer
A malfunctioning engine sensor can cause a variety of issues in your car key replacement audi. It is an important part of the transmission in your audi key fob since it sends information to the ECU about how fast or slowly the engine of the car is turning. This sensor can cause the transmission to malfunction and other components in the car to be affected.
The G5 engine sensor is located near the edge of the transmission, just above the flywheel ring. It sends signals via an uncolored wire to the ECU pin T55/49. The ECU uses this signal to control the flow of fuel and boost as well as timig. It also transmits it to the G5 Tachometer located in the instrument cluster. You can check for sensor failure by examining the continuity from the sensor to the tachometer. Also, you can examine the continuity between pins T55/49 of the ECU and pin T6a/1 of the instrument cluster (trace [79trace [79]) and between pin T6a/1 as well as pin T26a/12. It should show around 1000 ohms of resistance between those two pins. This is a common feature across the audi connect key 80-100-200-RS2 range, from the 1985 MC all the way up to the 1997 UrS An and 1995 RS2 DU You may also find some good ones in wrecking yards.