How to Go About boarding up windows and doors emergency boarding up a Door
A door can be boarded up as one method of protecting vacant investment properties from the elements. While it won't stop all destruction, it can help avoid some of the problems caused by severe storms.
commercial boarding up service up windows (please click the following web site) and doors can also deter burglars and vandals as well as squatters. Installing plywood panels over openings could be time-consuming and costly.
Take a measurement of the door
The first thing you'll need is a tape measure. You may also want to keep a ladder or chair handy in case you need to see more clearly at the top of the frame. Wear gloves and safety glasses in the event that you need to use these tools.
Once you have the measuring instrument, start by taking the door's width measurement. This can be accomplished by running the tape horizontally across the door. Be sure to eliminate any extra door parts like the door sweep to get this measurement. Next, take the height measurement by measuring from the floor to the existing sill plate or the lintel. It is important to measure multiple locations particularly with older doors, since they are not always a perfect rectangle. If the measurements differ, use the largest figure.
After you've taken the measurements of height and width, you'll need to figure out what size commercial boarding up service you need for the frame. It should be at minimum 2 inches larger and 1 inch taller than the door. 2 higher. This will allow you enough room to shim both the door and frame to fit.
It's a good idea to remove the casing or trim around the jambs of your door to observe the studs. This will help you to determine the exact dimensions of the gap between the studs and the frame.
After removing the trim, measure the width of your door frame using the tape measure. Take measurements of the frame at three different locations and then use the most compact measurement. Also, you should take a measurement of the height of the frame from top to bottom on both sides, and then use the shortest measurement as the height of your door.
If you are having trouble with the measurements, you should get a professional to your home and take the measurements. They'll be able to tell you exactly what kind of door and size you need and how to prepare the frame to accommodate a new door.
Plywood can be cut into pieces
A door frame is generally made boarding up services of a series thin boards or studs which create a hollow space surrounding the door. The typical door is held in place by two hinges attached to these studs. This means that if you want to refinish the door, it's essential to take the door from its hinges for a night. To keep insects out of your home and to secure the door opening, a straightforward method to board a door involves placing plywood into the opening. It is simple to do without the need to nail or screw the plywood to the door frame.
Plywood is easy to work with, affordable and looks great once it's completed. It is the ideal material to use as a temporary solution for a problem where you need to remove the door you have in place to finish it or build the new one. It can be used to secure the opening of a space being renovated, like an excavation site or basement.
For a wall constructed of plywood, start by taking measurements of the width and height of the door opening. Draw the measurements on the plywood with a utility knife and a drywall square or other straight edge of metal. Then, draw an outline of chalk across each of the lines you have marked to mark the areas you want to cut. Then, use a circular saw to cut the plywood to the desired size.
When cutting the plywood it is important to protect your eyes and ears. If possible wear protective goggles and earplugs while working. In addition, it's important to use a blade with a lot of teeth that will cut quickly and without tear-out. Utilize a small piece of wood to guide the blade. Hold it a hair's distance from the marked line when cutting.
A good way to keep the plywood in place without gluing it to the studs is to fasten a pair of short braces at each end. Set one brace on the inside of the door and the other on the outside. Install a deck screws in each hole, and then tighten using an open-end ratchet.
Fasten the Plywood
Once you have a sheet of plywood cut to the proper dimensions and with the holes for rails and stiles predrilled and ready to fasten the panel to the frame. This is a relatively straightforward project that does not require any extensive carpentry skills provided you follow the correct procedure and use the proper tools.
Begin by putting up a worktable near the doorway with two sawhorses and 2-by-4 framing lumber at each end of the table. Make marks during the measurement procedure to guide you in cutting the plywood. Score the lines with the help of a utility knife, a drywall square or any other metal straight edge. This will create an outline for the saw blade and help to prevent splintering during cutting the plywood.
Wear eye protection and use a circular table saw with a fine-toothed blade to cut along the scored line. Then sand the edges the plywood panel using 120-grit sandpaper to smooth the panels and remove any burrs that may have formed from the saw cuts. After sanding then apply a wood sealer and allow it to dry according to the manufacturer's instructions.
Install the hinges on the door frame. If you're using a T-hinge, drill holes on the outside side of your door to accommodate the straps portion of the hinges. Next, position the hinge's outside face on its mark and attach it to the frame with an screw gun. Repeat the procedure for each hinge on the inside of your door. Be careful not to overtighten them, or the panel could shift.
If you have only a single hinged outside door you can make the latch easier to close by placing an electrical wire through the loops on the outside hinges. Fold a small piece of connect wires in half and then thread it through the two holes on the outside of the door. Then twist the wires to lock the door.
Install the Plywood
Based on the measurements you have taken using the measurements you took, put the plywood in the door opening. Shim the header (top) of the frame and the sill (bottom). Utilize a level to make sure there's not any slop in the header or sill. If it isn't perfect you can place a second shim wherever it is needed and continue the process until the sill and the header are even.
Once the plywood has been put in place, secure it using the stainless-steel hinge bolts and wingnuts. Make use of a screwgun that has an attachment for hex heads to prevent removing the heads of the screws.
If your house has studs running along your doorway, you can drill hanger bolts into each of the framing members. This is much simpler than using a drywall saw to make the hole.
After putting the plywood in place, measure the width and the height of the door opening. If necessary, cut your bottom of the plywood to fit the height of your door frame. Cut two pieces of framing wood 1-by-6 as braces for the lower and upper ends. Cut along the lines that are marked on the plywood with circular blades with teeth that are finely tipped. Wear eye protection. Take any splinters out of the cuts by using an the sanding block.
After you've placed the braces After you have placed the braces, use two pairs finishing nails of 2 inches to secure each brace to the plywood. After you're done, counter sink the heads of all the nails. The braces should be sealed with a quality wood sealing product, like the wipe-on polyurethane by Minwax.
If your door is too big, you can either add decorative molding to fill the gap between your door and jamb, or you can reduce the size of your opening. However, in most situations, it's more affordable and more convenient to find an alternative door. This will also take away any issues you might have had with the original door if it was damaged and could no fit for the opening.