Boarding Up Windows And Doors Tips To Relax Your Daily Lifethe One Boarding Up Windows And Doors Trick That Everybody Should Be Able To

boarding up windows and doors (click through the following web page) Before a Storm Hits

The act of boarding up a door up your windows and doorways before an event can give you the protection you need against damage. You'll require a few items to do this.

First, take measurements of the window's height and width including the framing (not the surrounding trim or masonry). Note these measurements down so you don't forget them.

Preparation

It is recommended to put up a board on doors and windows before a storm or other natural disaster hits. This will limit damage to property and decrease the risk of death. It requires a lot of planning to build a board around windows. You have to buy and measure plywood boards and you need to be aware of the exact dimensions of each window. It takes time to cut and install the boards correctly. Fortunately, the process can be simplified by starting the preparations when you first hear of a possible storm forming in your area. You can avoid stress at the last minute and make it simpler for you and your staff.

Start by listening to the forecasters of the weather and following the guidelines provided by your local government. The earlier you begin the process, you will have more time to gather the materials and keep them in storage without being overwhelmed by an approaching storm. It is possible that you will require a large amount of plywood to cover your windows dependent on the severity and imminence of the storm. Use a tape to measure the height and width of each window opening. Make sure to take into account the framing or trim around each window as well as any sills that are extended if applicable.

Then, determine the size of the plywood sheets you need by dividing the total window height and width by 2. If your window is wide of 16 inches, the thickness of each sheet is 8 inches. If you have an exterior made of wood, you should drill pilot holes in the plywood sheet to align with the frame of your window to avoid splitting when you screw in the screws.

For a window opening that is greater than the size of a single sheet of plywood can take cut two sheets that are each half the size of the desired window and set them side-byside on the wall. Then cut a piece 2 by 4 in (5.1 by 10.2 cm) lumber to the length of the connecting edges of the plywood sheets and then place it on top of the seam. Then screw 2.25 in (5.7cm) screws into the plywood sheet and into the bracing to join the two.

Materials

To ensure security and safety ensure safety and security, use only materials that are sturdy and will not be damaged or break in strong winds. Plywood is the most common material for commercial boarding up service up windows. It is easy to use, affordable and easily available. It's important to choose plywood that is specifically designed for exterior use (CDX) to ensure strength and is free of knots and warping. Storm shutters, also known as hurricane shutters, are a more robust option. They can be erected over windows that are already in place and offer better protection against shattered glasses and weather conditions that can be severe.

Once you've identified the position of the window openings then measure the width and height of each one to determine how much plywood you'll need. Use a power drill drill pilot holes into the plywood sheets around the windows at two-inch intervals. Mark the walls with studs prior to attaching the plywood to ensure the boards are fastened securely. If your home has wood siding, look for nailheads that might indicate the location of studs. In other cases, you can search for stud positions with your drill. Screws should be driven into the framing, not into the trim or sheathing. A plywood panel attached only to these materials can cause a safety risk in high winds.

If the size of your window is too large for a single sheet plywood, cut two pieces that are each the size you require and join them with 2 by 4 inches of lumber. Label each piece of plywood to let you know which window it will be covering.

To secure the plywood panels to the wall, make use of corrosion-resistant screws that are sufficient in length to penetrate both the sheathing as well as the studs. Aim to drive the screws into the studs in a way that they are about half the depth of the plywood is thick, but be careful not to go too deep and cause damage to the structure of your house.

In addition to protecting your windows, you should also put up a "No Trespassing" sign on your property and think about installing polycarbonate security glazing like DefenseLite over your primary windows. These transparent shields adhere to the existing glass to guard your doors and windows. They are virtually impossible to break, preventing criminals from breaking in.

Installation

If you live in a region that is prone to hurricanes or are planning to move to one the best way to protect yourself is to put up a board on your doors and windows prior to the danger of a storm arrives. This task can be completed quickly and efficiently, however only if the plywood sheets are cut, measured and labeled prior to the storm hits.

You'll need other tools as well which include a drill, a saw (or an hammer that has nails for those who don't have an electric tool) and an erecting level, gloves and safety glasses. It's a good idea apply sealant to the plywood, as well, to make it waterproof.

Begin by taking measurements of the width and height of each window opening, then cutting the plywood sheets so that they fit within the frames, with an overlap of 4 inches on all sides. It is best to do this on site, since it allows you to control the exact dimensions of the plywood.

Use a circular saw or track saw to cut the boards to the right size, and remember that you'll have to sand them down once they're put in. Once you've put your boards in place, screw 3-inch stainless steel hanger bolts into the framing studs around each window. Use washers to secure each bolt and wing nuts. Make sure that each screw is able to penetrate the studs at least two inches to ensure the board is strong enough to resist high winds.

If you're building with concrete blocks, you can connect the plywood with galvanized pan head screws that are driven into the overlapping edges of the panels into the masonry or cinder block. It is also necessary to make pilot holes in the masonry, and then screw corrosion-resistant screws through the holes. It's a job that could take as long as three hours per window, so it's crucial to begin the process immediately after you hear that a hurricane warning has been issued. This will give you time to finish your project before the storm arrives.

Maintenance

If you're a homeowner or business owner, it is essential to have the right materials to board up doors and windows ahead of a severe storm. This will help you to avoid expensive repairs and protect your home from further damage caused by rain, wind debris, flying objects and other causes.

Having the right materials will make the boarding up process faster and easier to complete. It is essential to precisely measure the windows. This will ensure that the OSB or plywood is fitted snugly, and that it will not fall off easily. If you are using plywood, make sure you use exterior grade sheets and consider adding a second protective finish.

Mark the places where the screws are going to be placed into the board after you have measured the OSB or plywood. Utilize a drill to predrill holes at 12-inch intervals into the plywood. This will allow you to securely fasten the boards with hanger bolts during an emergency boarding up service or in the event of a disaster. After the storm has gone away and you've received the all-clear from local authorities, remove the hanger bolts, but keep them in place for any future emergency boarding up 24/7 situations.

The next step is to put the plywood panels on top of the windows. This is a job for two people So, be prepared before starting. If you're using plywood, sand the edges to smooth them so they don't scratch paint or trim. Then, attach the frame to the plywood using corrosion-resistant screws that fit into the pilot holes. If your home has shingles made of vinyl it, attach the plywood directly to the shingles, and not the wood framing.

Besides keeping out rain and other weather elements, a boarded up window is also a great method to deter burglaries. Burglars are more likely to target a property boarding up with a window that is broken or one that's not locked. Also, they are more likely to break into the store with a boarded up window than one without. This is something that retail business owners should consider very seriously.