Reasons to Change Door Lock
You can alter the double glazing window locks replace glazing upvc window lock repairs near me lock replacement - anotepad.com - on your door for a variety of reasons, from increasing the security of your house to redecorating the entryway. You may need to change locks if your key gets stuck or becomes difficult to turn.
Change your lock is an easy project that even beginner DIY homeowners can tackle. Get the tools you need to begin.
Remove the lock from the old one.
The removal of the old lock from the door is a necessary step before installing the new lock. This is essential when you suspect that someone else may have access to the house. It's also a good idea following you've moved into a brand new home, suffered a break-in or welcomed a roommate. The process is simpler than you think and can be completed within just a few minutes.
Begin by removing the screws that hold the deadbolt faceplate onto the door frame. You will need to remove the screws on both sides of the door to take off the faceplate. This will allow you see what's behind it and give you an understanding of how to continue with the next steps.
After removing the faceplate you'll need to take off the bolt along with the strike plate and strike plate. Use a screwdriver to loosen the bolt, and then take it out of the hole in the door. If the bolt is rusty you might need to use a chisel smash it out. If you're using a chisel be careful not to scratch the door frame.
Make sure the new deadbolt, doorknob and lock will fit in the existing holes in the door before removing the old one. The majority of hardware stores and big box stores sell different kinds of locks and can assist you in finding the best one to meet your needs. Ask for help if the lock you purchased isn't the right one for your door.
While you're taking off the old lock, look for small slits or depressions in the handle or around the trim. If you find them, slip a straightened safety pin or flat screwdriver through them to open the handle and expose the screws beneath.
Once the screw in the handle has been removed you can begin to remove the knob from its spindle. To do this find the set screw at the base of the knob and loosen it. The next step is to remove the knob from the spindle and carefully remove the spindle from the door.
Install the new lock
It's a good idea to change the locks on your doors periodically particularly if you've experienced a burglary. It is easy, cheap and efficient to change the lock on your door. With a screwdriver and a few simple instructions most people can handle it themselves. You might also want to learn how you can change the lock's key to ensure that only you have the key.
To start the process, you must purchase a new lock that is compatible with your existing lock's keyway. Most locksmiths will replace your lock at a cost but you can save money by doing it yourself. You can purchase an entirely new lock from hardware stores or online. Standard deadbolts can be fitted to the majority of doors. However, you will have to measure the door to ensure that it will fit.
The majority times the lock you purchase will be supplied with the cardboard template that will show the way it will fit on the door. This template can be used to drill the hole. It's much simpler than having to measure every time. If the template doesn't match to the hole you intend to drill, you should take it back to the hardware store and get another one.
When installing the new lock, ensure that it is placed on the right side of the door. You can check this by looking at the latch, which must be labeled "up" or something similar. Check that the latch is seated correctly on the latch plate, then secure it with the screws provided.
If you are replacing the knob lock on your door It's important to pay attention to the handing. Most knob locks are left-handed however, there are some that are right-handed. If you are not careful, the knob could be installed on the wrong side of your door, which could make it impossible to lock from the inside or outside.
You should test the new lock after you finish. You should be able both to lock and unlock the door with a key from the inside as well as the outside. If you're not satisfied with the result you can always contact a professional locksmith to repair it.
Test the lock
If a lock on your door won't unlock is a hassle but it could also put your family's safety at risk. Luckily, it's easy to fix most issues with door locks by doing a bit of troubleshooting and lubrication. First, ensure that your key is properly cut and that the lock assembly isn't soiled or loose. If this doesn't fix the issue, try applying lubrication to the door lock actuator using powdered graphite or a silicone-based grease.
Ensure that the doorlock switch, wiring harnesses and actuator connector all work properly. To do this, consult the manual or wiring diagram to determine the function and color-coding of all door lock switch wires. Then, use a test light or digital meter to determine whether the door lock's actuator is receiving power and ground when the switches are turned on. If you notice the switches switch on and off with voltage this means that the switches are in good shape and the actuator is likely to need replacing.
If the switch seems to work however the actuator does not move when you turn the knob, it could be a problem with the actuator itself. The actuator cylinder has spring-loaded pins that prevent the cylinder from rotating until a key is inserted and pushes the pins upward to match the height of the key at the point of entry. In the end, this causes the cylinder to spin and open the lock body which allows the handle to latch.
If the door lock actuator is malfunctioning, you can take the switch and wires from the actuator by using small screwdrivers to unlock the locking bolt and remove the plastic cover that holds the electrical connector. Then, disconnect the door lock actuator, and let it fall. Then you should be able to locate and take off the two bolts of 10mm that hold the actuator in position. After the actuator has been removed, you should be able to disconnect the black electrical connector and pull it out together with the lock and actuator assembly.
Replace the key
If you have a keyed deadbolt or door knob when it isn't working correctly, you should either change the lock's key or rekey it or replace upvc window lock it completely. It's not too difficult and can save you money. It is best to hire a professional locksmith check the locks for any issues prior to beginning. This will give you peace of mind that your home is secure and safe.
Take off the exterior faceplate of the doorknob/deadbolt. There could be screws that hold it in place, you need to remove them, use a screwdriver to loosen them, and then pull the faceplate away. Then, take off the interior faceplate by using a screwdriver with a flat head. After you have removed the faceplate you can pull out the bolt and screw from the lock cylinder.
A locksmith can determine if you need to replace or rekey the lock. They can also offer suggestions on the most secure measures for your home. They can also make the necessary adjustments to your door and frame to ensure the perfect fit. They also offer the guarantee for their work.
If you choose to rekey the lock you must first purchase a new key for it. It's important to use the correct key in the lock. If you use a key that isn't right, it could cause damage to the internal mechanism and prevent it from working. Insert the key into the lock to test its size. If it fits flush with the plug, it's the right size. If the pins stick up from the top of plug and are not a good fit, they're too long.
You may want to replace window lock your door lock for many reasons, including:
If you're moving into an owner's home or if you lose keys, rekeying your lock can be a more affordable alternative than replacing it. It is also less invasive than a full replacement. Rekeying an existing lock may not be feasible in certain circumstances. If the lock has been damaged or repeatedly jammed, for instance it could be time to replace it.