Ghost Immobiliser Fitting
Guard your car from key theft, cloning and hacking with the first aftermarket CAN immobiliser. With the added option of connecting to a Ghost app and GPS tracking system that can notify you via phone in the event that your vehicle is damaged with or stolen.
The installation of a Ghost immobiliser can be done by a qualified technician. Having the right tools, insulation tape, and heat shrink tubing are essential.
Getting Started
Ghost immobilisers are a great alternative to physical theft devices such as car alarms and wheel locks. They protect your vehicle without the use of LED indicators or key fobs. They are directly connected to the ECU CAN data network, and can only be activated by entering a PIN code. This provides a more secure level of protection against key hacking, cloning, and even ECU swapping.
As a result, installing a ghost immobiliser Birmingham has to be done with great agility and precision. It's like walking through the minefield. A single mistake could cause severe damage to the circuits of the electrical system of your vehicle. It is important to understand the installation procedure and prepare your vehicle in a timely manner.
First, you need to prepare the vehicle by taking out interior panels to make room for the immobiliser device. Once you've found the perfect place to conceal it put it in place by using cable ties to stop it from being removed or tampered with. Clean up your wiring by making sure that loose wires are tied down and using insulation tape to cover any exposed connections. This reduces the risk of an accidental short circuit and improve the appearance and reducing the chance of theft.
Find a source of constant 12V power, as well as an earthing point for the ghost immobiliser cost immobiliser. Once you've located these and tested the power wires using a multimeter, to ensure they are delivering a consistent voltage. Finally, connect the CAN H and L wires from the immobiliser to the identified power source and the grounding point.
It is essential to ensure that all connections are checked and check the immobiliser for indications of corrosion. You should also test the system to make sure it's working correctly by entering a PIN code and then starting the engine. This should become a part of your routine, as it will allow you to spot any intermittent problems early. Regular testing can help extend the life of your device and keep it functioning at its peak.
Preparing the Vehicle
The installation of an Ghost 2 immobiliser immobiliser is a complex job that requires the appropriate tools and knowledge. A wiring diagram of the vehicle is essential to locate the right wires and establishing precise connections, while a multimeter can be used to verify the electrical properties and ensure security. Cable tie and insulation tape can be used to secure connections and prevent alteration. A user's manual will give you specific instructions specific to your Ghost Immobiliser model.
Once installed the ghost immobiliser will stop an unauthorised engine from starting by requiring the driver to enter a unique PIN sequence by pressing buttons on the steering wheel or centre console. The code can be altered at any time by the owner, either manually or remotely through a mobile app. The device also operates silently and is inaccessible to thieves as it does not emit radio frequency.
A ghost immobiliser is connected to the CAN bus of the vehicle, which is a network that communicates with the electronic control units (ECUs) of the vehicle. It intercepts signals sent by ECUs, and blocks the engine if a false one is detected. The system is weatherproof and tamperproof. It doesn't have any keys or LED indicators to draw thieves' attention.
It can be positioned behind the dashboard or in a hidden location, so that it isn't visible to thieves and doesn't interfere with the vehicle's performance. It can be mounted in a small jar, so that it is less likely to be spotted by fraudulent salespeople when they test drive.
Its stealthy operation and integration with the vehicle's CAN bus system makes it an effective deterrent against modern methods of theft, such as key cloning and signal relay attacks. Combining the system with other security measures will create a powerful barrier that can deter even the most persistent of thieves. This is why more insurance companies are recommending or even requiring ghost immobilisers to be installed, as it will significantly lower monthly premiums.
Making Connections
In contrast to traditional security systems that are heard by thieves, ghost immobilisers operate in a quiet manner to stop them from knowing that your vehicle has been switched on. They also prevent high-tech methods of stealing vehicles like OBD hacking. They can also be put in without causing permanent marks in your vehicle which makes them a great choice for people who plan to sell their vehicle in the near future.
The Autowatch Ghost 2 CANbus immobiliser is one of the latest and most reliable solutions to prevent car theft. It disables your engine using the CAN data network and generates a unique PIN code, which is difficult for criminals. It can be installed in many vehicles and is compatible with a variety of existing features, including car alarms, GPS trackers, steering wheel locks, and door lock bypass systems.
If you opt to use a Ghost immobiliser for your vehicle, be sure you refer to the wiring diagram to determine the wires that connect. Verify the location of these wires to ensure their accuracy and mark them with tape or labels to help you keep the track of them. It is also necessary to locate a reliable power source (12V) for the system, as well as the grounding. Once you have these in place, you are able to begin to make the connections needed to complete the installation.
The ghost immobiliser won't allow your vehicle to start until the pin code is entered via the buttons on the steering wheel or dashboard. This will stop ECU cloning and other methods of stealing vehicles. In addition, it could be paired with other approved by Thatcham security equipment, such as alarms and tyre clamps to give your car an even greater degree of security.
As the UK automotive industry grows, as do the options available to secure your car. With so many avenues for thieves to break in and take your car, it's vital to take every precaution to protect it from being stolen. Ghost immobilisers have become an increasingly popular option for car owners who are responsible.
Testing the System
The Ghost Immobiliser uses a CAN data network to communicate with the vehicle's ECU, preventing the engine from running until a specific PIN code is entered. This makes it extremely difficult for thieves to copy your key fob to open your vehicle, and even more difficult to disable the system by hacking its electronic.
Ghost Immobilisers can also be used in conjunction with GPS tracking devices to assist you to locate your vehicle if it is stolen. This feature is not an option that is commonly used in security products sold by the aftermarket, but it's a great way to enhance your security and provide peace of mind knowing that your vehicle is always protected.
In addition to providing enhanced security in addition to providing enhanced security, the Ghost-II immobiliser provides a simple user experience, removing the requirement for additional key fobs and devices. It has a simple, intuitive PIN code entry that integrates seamlessly into your daily routine. It also offers convenience features and deactivation modes that allow you to temporarily disable the immobiliser to valet park or service your vehicle.
Before you begin the installation process, familiarise yourself with your vehicle's wiring and prepare the required tools. A basic set will enable you to make precise connections. A multimeter is a tool to test electrical values. Insulation tape and heat shrink tubing are also crucial to protect connections from short circuits, while cable tie is a great way to keep the wiring in the correct position. It is also essential to be in a well-lit space and wear appropriate safety gear when working with electrical tools and components.
You should test the Ghost immobiliser after you have completed the installation to ensure it's working correctly. It is recommended to first start the car stolen with ghost immobiliser without entering the PIN. If this fails then you'll need to try again and check the connections more thoroughly.
The Ghost Immobiliser, unlike other security systems, is a secret device which cannot be detected by thieves. It is also far more efficient than physical deterrents, such as wheel clamps and steering locks. It is TASSA acknowledged and approved by some insurance companies, making it an investment that is cost-effective and can give you peace of mind you deserve.