Car Key Button Repair
A damaged car key button can be frustrating. You may need to contact an emergency locksmith service or purchase a replacement remote.
However, you may be saving money by repairing an old key fob instead of replacing it. This is especially true when the problem is caused by an old switch or a damaged contact.
Battery
If your key fob's buttons are not responding to your pressing them, it could be a sign that the battery has died or is nearing its end of life. It's easy to replace the battery on your own, rather than paying for locksmiths or dealers.
First find the battery compartment. The battery compartment is usually located on the back of the key fob, and can be hidden behind a cover that slides out or an open button that opens the access point. After the compartment is exposed, look for the small button-cell battery. This is typically shaped like an oblong coin and is has the plus and minus signs. Remove the battery that is old, and replace it with a brand new one. Make sure the plus and the minus symbols are properly aligned.
Once the battery is in place Close the compartment and snap the two halves of the key fob together. Before closing the door ensure that you align and snap the components in place. Press any of the buttons to confirm that they function properly.
If the remote key fob repairs keyfob doesn't work after replacing the battery, there could be other issues that require a different form of repair. Dropping the device in a puddle could cause it to cease functioning. It could also be due to a malfunction with the internal electrical system, or it may need to be deprogrammed. Take a look at these other car troubleshooting tips to see whether your auto key repair near me fob is experiencing a different issue.
Switches
There are many kinds of switches used in the car key fob, dependent on the year and make. The older model keys usually have a separate chip that is visible in the case, whereas modern keys are more sophisticated and work by sending signals to the car. Whatever the model of key, the buttons on the key repair car can become worn out or damaged when used regularly. The result is they become difficult to press, or even unresponsive. If you try to press the button too hard it could cause further damage and may even stop the key from being able to start your vehicle in the future.
If your key doesn't appear to be working, you should first try changing the battery. If this doesn't work, then you may have to clean your key fob or re-adjust its switches. These tiny electronic switches are more susceptible than larger parts of the key to break due to the fact that they are constantly tossed around.
The switches are rubber-like and are coated with an electric conductor film that can wear down over time. Luckily, they're also a very small part and affordable to replace. They're soldered to the circuit board, so you need to carefully take them off without causing any damage to anything else. You can then solder new ones in and reassemble your fob.
Do not use your car key fob for more than an hour at a time and don't leave it out in the open. Also, you should find a secure place to store your keys when you aren't making use of it.
If the problem persists after you've cleaned your key repair shop fob replaced the battery and attempted to clean it, you may need to consult a locksmith. A professional can check the frequency of your key to determine whether it's still able communicate with your vehicle. They can also open and replace micro switches, swap cases and much more.
Outer Case
If the buttons don't move freely up and down in the case, they may get stuck or break. If cleaning the case using rubbing alcohol and a cotton swab does not work, it could be necessary to take off the case. If the contact points where the buttons touch don't fit well or are worn out, adjusting them could be the only option to fix the problem.
Certain keys have rubber buttons which can wear out over time. Rubber buttons can become difficult to press when they stretch, and nails could scratch them. In this scenario the key could fail and it's time to replace the case or button. This repair involves removing the remote, then locating the button switches on the circuit board, and then heating the solder and carefully removing them. New buttons are then attached to the circuit board. The case can be reassembled and the horseshoe key blade piece can be attached. The new buttons must be fitted snugly into the case in order to prevent them from falling out.
Inner Case
Since your key fob is likely to be tossed around and occasionally be pressed by accident and the buttons inside may become stuck or broken over time. Utilizing metallic tape and a hole punch you can often quickly solve this issue in the event that your vehicle is away from home when the key fob won't work and you are unable to open the doors, but not start the engine. This quick fix could enable you to safely get back to your vehicle and complete your journey.