Reasons Why Your nissan nv200 key Qashqai Key Fob Won't Work
The Qashqai has a distinctly SUV-like appearance due to its bigger dimensions, and the ride on 19-inch wheels in Ti and ST-L models can be a bit stiff at times. The front tyres in the Qashqai are also prone to losing grip on bumpy surfaces, and its CVT can occasionally display a wrist-flexing torque steering.
This is typically caused by an unresponsive battery, which can be replaced in just a few minutes. Make sure that the replacement battery is of the same voltage, size and specification.
Water Damage
One of the most common reasons that a nissan lost Keys key fob displays the "key ID is not correct" message is due to water damage. The rubber seals on the key fob shield the electronic chip, but prolonged exposure to moisture could cause it to stop working properly. This is often the case when you drop your key fob into the ocean or in a swimming pools, but it could happen when it's wet due to soapy hands or rain.
If your key fob is exposed to water for an extended time, it may need to be cleaned using isopropyl alcohol or an electronic cleaner. It may also need to be taken to an expert for repair or replacement key for nissan.
If your key fob is in need to be replaced, it is an easy process. Make sure you have the proper multipack (CR2032 3V). Open the front and rear cases with the flat-head screwdriver. Remove the clips made of metal, then remove the battery that was in place and replace it. Reassemble the fob and replace the mechanical key. Check to see if it functions properly. If it isn't, you'll need to take it to an Nissan dealer or professional auto locksmith to replace the chip in the key. Fortunately, the chip is not typically damaged by exposure to water and therefore this shouldn't cost you a lot.
Dead Coin Battery
The coin battery is another common reason why your Nissan Qashqai remote key fob may not work. The batteries typically last for 3-5 years, but they may fail over time, especially when the fob is dropped frequently. You could try replacing the battery with a new one, but be sure that it's the same voltage and size as the original. If you install a new battery, it could cause the key to be assigned a different key ID. This will prevent it from being linked to your vehicle.
The most efficient method of replacing the battery of a coin on a Nissan Qashqai key fob is by opening the key fob using an small screwdriver that has a flat head. The screwdriver should be inserted into a small notch at the bottom of the key fob. Make sure to gently twist the screwdriver to separate the two halves. Remove the old CR2025 battery and replace it with a brand new one, noting the position of the old one in the fob.
Before putting the new battery into place check to ensure there is no dirt or water damage on the terminals. If not, clean the terminals using some isopropyl ethanol. You'll also want to make sure the pole cables are plugged in correctly - they should be connected to the negative and positive poles of your battery, respectively.
Troubleshooting
If your Nissan Qashqai key fob stops working after exposure to pure rain or tap water, it may be a sign of an internal chip problem. A battery change won't solve this, and you'll have to buy an entirely new key fob. If you dropped the key fob on the ground and it stopped working instantly it's most likely because it damaged the internal chip. You can usually get the key fob to function again if you take it out and clean the chip using alcohol and paper towels before putting it back in.
Key ID Incorrect is a common error that can be seen on the dashboard of your car. The vehicle is unable recognize the key fob and thus won't allow the car to start. This problem could be caused in numerous ways, including water damage, issues that are undetectable within the key fob circuitry or RFID interference.
The key fob won't work in the event that the 12 volt batteries are not working or provide enough electrical current. This will affect the remote keyless system and central locking of your Nissan Qashqai, as well as hindering you from starting the engine using the key fob (if equipped with Intelligent Key). If you're unable to lock or unlock the door manually you must check the batteries on your key fob to make sure they're in good condition. Try replacing the battery to reset your transmitter.
Reprogramming
If the key fob is not been submerged in salt water the device should be able to come back to life after a quick rinse with clean water. You can also clean the electronic component using isopropyl or electronic cleaner. If these don't work It could be the time to replace the entire key fob with a brand new one.
If your nissan almera key programming Intelligent Key still does not work, there could be a connection issue between it and the vehicle. Start by turning the ignition switch without beginning the car. Keep doing this until you see the hazard lights flash twice. Turn off the car and take out the key.
Next, you must open the fob compartment inside your vehicle. It's usually located on a door's jamb or the handle for the driver's door. Find the small "program" button and press it. Once the process is completed, you should hear a chime.
Now that your Intelligent Key is relinked to the car is the time to test it out. Press all the buttons on the key while standing a distance from the car. If the lights flash, or the horn sounds, the key is connected to the Nissan. You can also test it close to the Nissan.