Car Key Button Repair
A damaged car key button is frustrating. It is possible to call the 24 hour Locksmith Service or purchase an alternative remote.
However, you might be able to save money by fixing an old key fob instead of replacing it. This is especially true when the issue is due to a worn switch or faulty contact.
Battery
If the buttons on your key fob aren't responding when you pressing them, it could be a sign that the battery has failed or is about to reach the end of life. It's simple to replace the battery on your own instead of paying locksmiths or dealers.
First look for the battery compartment. This is usually found on the backside of the key fob and might be hidden behind an open cover that slides out or an access point which opens when you press a button. Once the compartment is opened then you will find the small battery. It's usually shaped like an ordinary coin and is has a plus and minus symbol. Take the battery out and put a brand new one in its place, ensuring that the plus and minus signs are correctly aligned.
Once the battery is installed close the compartment and snap the two halves of the key fob together. Before closing the door ensure that you align and snap the parts into the correct position. Press any of the buttons to verify that they function properly.
If your remote key fob ceases functioning even after replacing the battery, it could be suffering from other issues that require a different kind of repair. Physical damage from dropping the fob into a puddle, for instance could cause it to cease functioning altogether. It could also be due to a malfunction with the internal electrical system or need to be deprogrammed. Try to figure out what's wrong with your key fob using these other common car troubleshooting techniques.
Switches
Depending on the year and the make, there are different kinds of switches available in the keyfob of your car. The older model of key often has a separate chip that is visible inside the case, while the modern keys are more sophisticated and function by sending signals to the car. The buttons on a key fob repair service may be worn out or damaged due to regular use, irrespective of the model. This causes them to become difficult to press or even unresponsive. If you attempt to force the button to function it could cause further damage and may even stop the key fob repairs from being able to start your vehicle in the future.
If your key doesn't seem to be working, first try changing the battery. If that doesn't work it may be necessary to clean your key fob and re-adjust the switches. These tiny electronic switches are more likely than larger components of the key to break because they are constantly tossed around.
The switches have a rubbery feel and are coated with a film that conducts electricity. This film can wear off over time. However, they're small and easy to replace. They're soldered on the circuit board, which means you must carefully remove the old ones without damaging other components. You can then solder the new ones into and then reassemble your fob.
A good way to keep your car key fob from getting damaged is to not use it for more than a few hours at a time, and also to not leave it in areas that it will be visible. Also, you should find a secure place to keep your key in when you're not using it.
If you've tried cleaning your key fob or replacing the battery, and the issue persists, it may be time to think about hiring an appointment with a locksmith. A professional locksmith will test your key's frequency to see whether your vehicle is capable of communicating. They can also open and replace microswitches, alter cases, and much more.
Outer Case
If the buttons can't move freely in the case, they may get stuck or break. If cleaning the case with rubbing alcohol and a cotton swab does not work, it may be necessary to remove the case. If the contact points where the buttons touch aren't fitting well or are worn out, adjusting them might be the only way to correct the issue.
Rubber buttons be worn out over time. The buttons made of rubber can become difficult to press as they stretch, and nails could cut them. In this case, the key may fail and it's time to replace the case or button. This repair car key remote involves removing the remote, finding the button switches on the circuit board, then heating the solder and carefully remove them. The circuit board is then soldered with new buttons. The case is then rebuilt with the horse shoe key blade piece inserted. The new buttons should be snugly fitted inside the case to keep them from falling out.
Inner Case
Over time, your key fob's buttons can become damaged or stuck because of the constant jolting and accidental pressing. Utilizing metal tape and a hole-punch, you can usually solve this issue when your car isn't at home and the key fob doesn't work and allows you to open the doors, but not to start the engine. This simple fix will enable you to safely make it back to your car and complete your journey.